GRAUPNER Falcon 12 Скачать руководство пользователя страница 31

Страница: 31 / 52

31 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Transmitter presettings

• Select free / deleted model memory and initialize with model

type "helicopter".

• Set "Pitch front/back" according to your personal preferences

and do not change it anymore.

• Set all trims to "0" or leave them, never change them in flight. If

possible, the trims should be deactivated in the transmitter for

safety's sake, for example by setting the trim step to "0".

• As a swashplate type "1 Servo" is to be activated or left. (The

swash plate mixers take place in the receiver).

• All servo travel and direction settings will remain at their default

values for the moment. So on 100% servo travel and "normal"

direction of rotation. Likewise, no further programming, in par-

ticular in the heli-specific area, may be undertaken.

• Bind the receiver to the transmitter.

Initialize the receiver

Each time the model is powered up, the gyros are immediately active

but not yet calibrated. Since calibration is only performed on a quiet

receiver, the model should be kept steady when switched on. As

soon as the swashplate moves briefly three times in the idle position

after approx. 3 seconds, the initialization has been successfully com-

pleted and the calibration is completed.
This process must be awaited each time the receiver system is

switched on before the model can be started!

Basic settings

Procedure

1. After successful preparation of the transmitter and the helicop-

ter, the telemetry menu of the transmitter must be called up

according to the respective transmitter instructions.

2. In the receiver menu, the model type is set to "Heli", see illustra-

tion on the left.

3. Since the sequence of the subsequent display descriptions is

based on the order in the receiver, the first step in the initial

setup of a helicopter is to change to the menu "Basic settings

control". (The menus between them are only relevant after-

wards!)

Note

The following display illustrations always show the respective

default values.

RECEIVER 2.03

ALARM VOLT: 3.8V

ALARM TEMP: 70°C
Max. altitude: 0m

LANGUAGE: English
Ant1 100% Ant2 100%

Period: 20ms

Model type:

Heli

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды