GRAUPNER Falcon 12 Скачать руководство пользователя страница 23

Страница: 23 / 52

23 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Butterfly mixer with elevator addition

FREE MIXER

FROM CHANNEL: 1

TRIM: +0%
TRAVEL–: +100%

MIXER 1

: +100%

TO CHANNEL: 2

FREE MIXER

FROM CHANNEL: 1

TRIM: +0%
TRAVEL–: +100%

MIXER 2

: +100%

TO CHANNEL: 5

FREE MIXER

FROM CHANNEL: 1

TRIM: +0%
TRAVEL–: +10%

MIXER 3

: +10%

TO CHANNEL: 3

Notes

• These mixers may only be needed on transmitters without trans-

mitter-side butterfly mixers.

• The respective travel setting must be adapted to the model and

made so that the servos never stall mechanically.

Display "Gyro setting"

Preparation step-by-step

1. With deactivated gyroscope, carefully trim the model on one or

more trim flights on the transmitter side.

2. Switch the receiver off and on again to transfer the flown trim

state to the memory of the receiver.

3. Enable gyro control as described below.
4. Set the factor for gyro correction, eventually check the values for

the single control surfaces.

MODE

Gyro setting

MODE RU 0

Aile: 5
Elev: 5

MODE AI/EL 0

Rudd: 5

Factor: OFF

The mode can be set separately for AILE/ELEV and RUDD.
The mode can be set permanently or it can be switched through an

assignable control channel. If a proportional control is assigned to

the selected control channel in the transmitter, the respective mode

can be activated in the following setting ranges of the maximum pos-

sible servo travel:

Mode

Range

0 (no regulation)

–150 % … –75 %

1 (normal regulation)

–75 % … –25%

2 (Heading Lock mode with suppress.)
(In stick center position Heading-Lock

acts. Outside the stick neutral position

the gyro control is active.)

–25 % … +25 %

3 (Rate mode)
(In the stick neutral position Hea-

ding-Lock acts over the entire control

area)

+25 % … +150 %

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды