manualshive.com logo in svg

GRAUPNER Falcon 12, Руководство пользователя

Поделиться
Скачать
GRAUPNER Falcon 12 Скачать руководство пользователя страница 21

21 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Displays "Fixed-wing models"

Display "Free mixer"

Notes

When using the gyro, see the following description of the display 

page "Gyro setting", ...

•  ... always set the number of ailerons in the transmitter accord-

ing to the respective transmitter instructions.

•  ... the tail type must always be set to "normal" in the transmit-

ter. 
V-tail, delta wing models or, for example, two elevator servos 

must never be controlled via the mixers of the transmitter but 

only via the mixer of the receiver, otherwise the gyro stabiliza-

tion will only work on one side!

•  The five receiver mixers work "downstream" of the gyros.
•  If mixing functions are already programmed in the menu "Wing 

mixer" or "Free mixer" of your HoTT transmitter, make sure that 

these mixers do not overlap with those of this menu!

MIXER

 FREE MIXER

FROM CHANNEL:      0

TRIM:            +0%
TRAVEL–:       +100%

MIXER            1

:       +100%

TO CHANNEL:        0

In this line you have to select the mixers 1 ... 5 to be set. 
The following settings only affect the mixer selected in this line.

FROM CHANNEL

The signal applied to the selected control channel is mixed with the 

target channel (TO CHANNEL) to an adjustable extent. The method 

of setting up the values is analogous to the “Free mixers” menu in 

HoTT transmitters.
If no mixer has to be set, select "0". 

TO CHANNEL

Part of the source channel signal (FROM CHANNEL) is mixed into the 

target channel (TO CHANNEL). 
The mixer ratio is determined by the percentage values entered in 

the “TRAVEL-” and “” lines. 
If no mixer has to be set, select "0". 

TRIM

Similar to the trim function of the transmitter, a trim value in the 

range of ±50% can be entered in this line.

Содержание Falcon 12





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды