GRAUPNER Falcon 12 Скачать руководство пользователя страница 17

Страница: 17 / 52

17 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

"Telemetry" menu

SETTING & DATA VIEW

TELEMETRY

SETTING & DATA VIEW

SENSOR

DISPLAY RF STATUS

SELECT ANNOUNCE

RX DATA ON

ALARM SETTING

The basic handling of the "Telemetry" menu is described in the

respective transmitter instructions or the instructions of the Smart-

Box. By way of derogation, only in certain receivers the menu struc-

ture is summarized under the generic term "setting & data view".

These instructions also provide information on how to access this

menu. Change accordingly to the first setting page of the

Falcon 12

(plus)

GR-18

GR-24 PRO

HoTT

receiver.

Note

The setting values shown in the following display illustrations always

show the standard values.

Display "Receiver"

Language

In the "Language" line is set the display language in the receiver

menu.
The choices are: German, English, French, Italian, Spanish

Ant1 and Ant2

The percentages behind "Ant1" and "Ant2" indicate how high the

receive power is in percent of the respective antenna.
The display is mainly used to find the correct position of the anten-

nas during the installation.

Model Type

Depending on the selected model type "HELI" or "Airplane" different

menu pages are displayed. At a change from Airplane to Heli, after

power off and on the heli menu will be reset to defaults.

ALARM VOLT

If the voltage of the receiver power supply falls below the set value,

a low-voltage warning is generated by the transmitter in the form of

a "general alarm tone" (regular beeping at a rate of approx. one beep

per second) or the "receiver voltage" speech output message.

ALARM TEMP

If the receiver temperature exceeds the set temperature, a warning

is generated by the transmitter in the form of a "general alarm tone"

(regular beeping at a rate of approx. one beep per second) or the

"receiver temperature" speech output message.

S1019.AIR GR-18 without

vario

RECEIVER 2.03

ALARM VOLT: 3.8V
ALARM TEMP: 70°C

SUMD at CH6: No

LANGUAGE: English

CH9: SERVO

Ant1 100% Ant2 100%

Period: 20ms

Model type: Airplane

S1034 Falcon 12 plus

RECEIVER 2.05

ALARM VOLT:     3.8V
ALARM TEMP:     70°C
Max. altitude:    0m

SUMD at CH5: No

LANGUAGE: English

CH6: SERVO

Ant1 100% Ant2 100%

Period: 20ms

Model type: Airplane

CH5: SERVO

S1035 Falcon 12

RECEIVER 2.05

ALARM VOLT: 3.8V
ALARM TEMP: 70°C

SUMD at CH5: No

LANGUAGE: English

CH6: SERVO

Period: 20ms

Model type: Airplane

CH5: SERVO

33579 GR-18 with vario

RECEIVER 2.04

ALARM VOLT:     3.8V
ALARM TEMP:     70°C
Max. altitude:    0m

SUMD at CH6: No

LANGUAGE: English

CH9: SERVO

Ant1 100% Ant2 100%

Period: 20ms

Model type: Airplane

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды