manualshive.com logo in svg

GRAUPNER Falcon 12, Руководство пользователя

Поделиться
Скачать
GRAUPNER Falcon 12 Скачать руководство пользователя страница 15

15 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Receiver GR-18 HoTT and GR-24 PRO HoTT

Binding step-by-step

1.  Prepare the transmitter to be bound according to its instructions 

for binding.

2.  Switch the receiver power supply on.

The LED of a receiver 

GR-18 HoTT

 or 

GR-24 PRO HoTT

 lights up 

constantly red.

3.  Push and hold for about three seconds the SET button on the 

receiver.

4.  Start the transmitter-side binding according to the instructions of 

the transmitter:

 

ശ

If the LED of the receiver 

GR-18 HoTT

 or 

GR-24 PRO HoTT

 

starts to light constantly green within approximately three 

seconds, the binding process has been completed success-

fully.
The transmitter/receiver combination is ready for operation.

 

ശ

If the LED of a receiver 

GR-18 HoTT

 or 

GR-24 PRO HoTT

 

remains solid red, the "bind" or "Binding" has failed. Change 

the positions of the associated antennas and try the entire 

procedure again.

Receiver reset

Reset the receiver settings step-by-step

1.  As described in the submenu "Setting & data view" of the telem-

etry menu described below, in the line "Model Type" of the display 

page "Receiver" switch from "Airplane" to "Heli", or vice versa.

2.  Push or press the ENT key or equivalent.
3.  Disconnect the power supply and reconnect it.
4.  In the "Model type" line change the model type from "Heli" to 

"Airplane", or vice versa.

5.  Push or press the ENT key or equivalent.
6.  Disconnect the power supply and reconnect it.

The receiver is reset to factory settings.

Содержание Falcon 12





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды