GRAUPNER Falcon 12 Скачать руководство пользователя страница 14

Страница: 14 / 52

14 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Binding

To establish a connection with the transmitter, the

Graupner

HoTT

receiver must first be "bound" to at least one model memory in "its"

Graupner

HoTT transmitter. This process is generally called "bind-

ing". However, the method to be used is not always the same, which

is why the following step-by-step instructions apply only to binding

the specified receivers to any transmitter:

Receiver Falcon 12 (plus)

Binding step-by-step

• If the receiver is already bound to a specific transmitter and this

binding should be maintained, the transmitter should ideally be

switched on before the receiver. At the latest, however, within

approximately 15 seconds from the moment when the receiver

is switched on, the red LED of the receiver is constantly on.

Attention

As soon as the LED starts to flash, the receiver is in bind mode.

From this point on, there is a risk that the receiver inadvertently

binds to another HoTT transmitter, which also happens to be in

the bind mode at the same time and in the same place, where-

upon the model can run uncontrolled at any time.

• If the receiver is unbound or it should be bound to another trans-

mitter or only the model memory has to be changed than the

previous one, proceed as follows:

1. Prepare the transmitter or model memory to be bound accord-

ing to the instructions for binding.

2. Switch the receiver power supply on.
3. The LED of the receiver

Falcon 12 (plus) HoTT

lights up con-

stantly red.

4. Approximately 15 seconds after the receiver is switched on,

its red LED starts to flash, indicating that the receiver is now

in bind mode.

5. Start the transmitter-side binding according to the instruc-

tions of the transmitter.

6. If the red LED of the receiver goes out within about three sec-

onds, the binding process has been completed successfully.

7. Your transmitter/receiver combination is ready for operation.
8. If the LED on the receiver remains still red, the "binding" has

failed. Change the positions of the associated antennas and

try the entire procedure again.

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды