GRAUPNER Falcon 12 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

background image

13 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Connections

Connect the devices that have to be connected to the receiver to the

row of sockets on one end of the receiver. The servo connections of

the

Graupner

-HoTT receiver are numbered.

The polarity of the plug-in system cannot be reversed. Do not apply

force, but insert the plugs to the stop as far as they will go.

Note

For the receivers Falcon 12 and 12 plus, insert the plugs with the

brown or black cable upwards, until the stop.

Power supply

For the battery connection are designated the ports provided with

an additional "B". With the exception of connector 9 of the receiver

GR-18 HoTT

, a battery can in principle be connected to any free

socket. By V- or Y-cable also with any remote control component. We

recommend that you connect the power supply to the socket(s)

close to the servos already connected to the receiver. If you wish to

connect multiple separate batteries, the batteries must be of the

same nominal voltage and capacity. Never connect different battery

types or batteries with strongly different charges since this can cause

an effect similar to a short circuit. In order to avoid such effects from

the outset, voltage stabilizers such as PRX-5A receiver power sup-

plies (No. 4136) should always be connected between the batteries

and the receiver in such cases.

Attention

When selecting and connecting a power supply, be aware that

although the operating range of the receiver ranges from 3.6 to 8.4

V. However, practically all of the previously marketed servos, speed

controllers, gyros, etc. as well as many which are offered today have

a permissible operating voltage range of 4.8 to 6 V.

«
...
11
12
13
14
15
...
»

Содержание Falcon 12





















































Отзывы:

Нет отзывов

Похожие инструкции для Falcon 12

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 44

Бренд: Harman Kardon Страницы: 176

Бренд: Harman Kardon Страницы: 3

Бренд: Kathrein Страницы: 68

Бренд: Kathrein Страницы: 48

Бренд: Kathrein Страницы: 40

Бренд: Kathrein Страницы: 61

Бренд: Kathrein Страницы: 56

Бренд: Kathrein Страницы: 36

Euroline UFE 341S

Бренд: Kathrein Страницы: 36

TRIPP LITE Series

Бренд: Eaton Страницы: 16

Бренд: Icom Страницы: 125

Бренд: Renault Страницы: 384

Personal PA Receiver PPA R35N

Бренд: Williams Sound Страницы: 6

Бренд: Invisible systems Страницы: 15

FTDX 9000 Series

Бренд: Yaesu Страницы: 12

Бренд: Leica Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды