GRAUPNER Falcon 12 Скачать руководство пользователя страница 10

Страница: 10 / 52

10 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Symbol description

Always observe the information indicated by these warning signs.

Particularly those which are additionally marked with the words

CAUTION

WARNING

The signal word

WARNING

indicates the potential for serious injury,

the signal word

CAUTION

indicates possibility of lighter injuries.

The signal word

Note

indicates potential malfunctions.

Attention

indicates potential damages to objects.

Safety notes

These safety instructions are intended not only to protect the prod-

uct, but also for your own and other people’s safety. Therefore please

read this section very carefully before using the product!

Do not leave the packaging material lying around, this could be a

dangerous toy for children.
• Persons, including children, with reduced physical, sensory or

mental capabilities, or lack of experience or knowledge, or not

capable to use safely the receiver must not use the receiver with-

out supervision or instruction by a responsible person.

• Operation and use of radio-controlled models needs to be learnt!

If you have never driven such a model, then start extra carefully

and make sure to be familiar with the reactions of the model to

the remote control commands. Proceed responsibly.

• First, always perform a range and function test on the ground (to

do so, hold your model tight), before you use your model. Repeat

the test with running motor and with short throttle bursts.

• Before you start using the remote control model, you have to

check the further relevant laws and regulations. These laws you

must obey in every case. Pay attention to the possibly different

laws of the countries.

• The insurance is mandatory for all kinds of model operation. If

you already have one, please inform yourself if the operation of

the respective model is covered by your insurance. If this is not

the case, conclude a special liability insurance policy for models.

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды