background image

LDK 5307 7-inch LCD HD color viewfinder User’s Guide (v1.0)

7

Important information

Read this information carefully before installing this equipment and retain them for 
future reference. Read and comply with the warning and caution notices that appear 
in the manual. Any changes or modifications not expressly approved in this manual 
could void your authority to operate this equipment.

Safety Summary

This information is intended as a guide for trained and qualified personnel who are 
aware of the dangers involved in handling potentially hazardous electrical/electronic 
equipment. It is not intended to contain a complete list of all safety precautions 
which should be observed by personnel in using this or other electronic equipment. 

The installation of this equipment involves risks both to personnel and equipment 
and must be performed only by qualified personnel exercising due care. 

During installation and operation of this equipment, local building safety and fire 
protection standards must be observed. 

Whenever it is likely that safe operation is impaired, the apparatus must be made 
inoperative and secured against any unintended operation. The appropriate servicing 
authority must then be informed. For example, safety is likely to be impaired if the 
apparatus fails to perform the intended function or shows visible damage. 

The unit is protected according to IEC 60529 IPX54 (dust-protected and resistant to 
splashing water).

Warnings

Warnings indicate danger that requires correct procedures or practices to prevent 
death or injury to personnel. 

Do not modify this equipment;

Do not use any accessories other than those recommended by the 
manufacturer;

In case of an emergency ensure that the power is disconnected;

Mount equipment so that power lead can be accessed to disconnect power;

There are no user serviceable parts inside. Refer servicing to qualified 
personnel only or contact your local Grass Valley representative;

Observe local building safety, fire protection and electrical installation 
standards during installation and operation of this equipment;

Whenever it is likely that safe operation is impaired, the apparatus must be 
made inoperative and secured against any unintended operation.

Содержание LDK 5307









































Отзывы: