GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 138

GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 111

111

KMV-3901/KMV-3911

Installation & Service Manual

6 If the

Select USB Drive

window appears, click the letter corresponding to the USB key

you inserted in step 2, and then click

Select

.

7 When prompted to select an update file, locate and open the following Kaleido

Software operating system file, with the following format:

kmvos-

9.00_build_xxxx.os

The

.os

file will be copied to the USB key. This may take a few minutes.

When the copying process has finished, a message appears.

8 Click

OK

.

9 Click

EXIT

on the startup screen.

10 Click the

Safely Remove Hardware

icon

in your desktop’s notification area, and

then click the USB key on the menu. When a message informs you that it is safe to
remove the key, do so.

Upgrading the Kaleido Software and Firmware

At this point, you are ready to upgrade the Kaleido system software and firmware. The
multiviewer should be powered up, with an active monitor wall display. You will need
access to the monitor wall to observe the progress of the upgrade, and you will use a
mouse to trigger a system restart from the monitor wall, once the upgrade has completed:

• If you have a Kaleido-RCP2, make sure that it is connected, and that you can use the

mouse to move the pointer on the monitor wall. If the mouse is unresponsive, try
rebooting the Kaleido-RCP2 by pressing ENTER+ESC+DEL on the Kaleido-RCP2’s
keypad.

• If your system does not include a Kaleido-RCP2, connect the mouse directly to a

USB port on the multiviewer, and then make sure you can move the pointer on the
monitor wall. See

Troubleshooting with the card's front edge USB connector

page 115 for more information about using the USB port on the multiviewer.

«
...
109
110
111
112
113
...
»

Содержание KMV-3901











































































































































Отзывы:

Нет отзывов