GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 11

Страница: 11 / 138

KMV-3901/KMV-3911

Installation & Service Manual

Overview of single card functionality

Features

Unmatched Space Efficiency

• 20 quad-splits, or ten 8-input KMV-3901/3911 multiviewer cards, per 3RU frame

• Fully loaded frame with 10 cards weighs only 9.9 kg (21.8 lbs)

Low Power Consumption

• 300 Watts for fully loaded 3RU frame with 10 cards and up to 20 outputs

• 24 Watts per dual-output card

Super Silent

• Ideal for installation within studios, control rooms and trucks

High Quality, Flexible Monitoring

• Outstanding multiviewer picture quality, based on award-winning Kaleido technology,

with all essential display elements for production

• Choice of single multiviewer output per card with up to 8 pictures, or dual quad-split

displays

• The KMV-3911 supports up to two HD-SDI monitoring outputs (one associated with

Head

1, and one with Head

2 if enabled), with embedded audio

Router Integration

• Tight integration with NVISION and third party routers allows expansion up to

1152 inputs and 288 multiviewer outputs

• Multiple multiviewer outputs can be controlled from a single panel

Ultra-Resilient

• Hot-swappable cards with Auto-Recovery for configuring cold replacement cards

during maintenance

• 3RU frame features dual hot-swappable power supplies and fans plus redundant

Ethernet

Содержание KMV-3901











































































































































Результаты поиска

Содержание KMV-3901

Отзывы:

GRASS VALLEY KMV-3901, Инструкция по установке и обслуживанию, Страница: 11 / 138

Результаты поиска

Содержание KMV-3901

Отзывы: