GRASS VALLEY K2 SAN Скачать руководство пользователя страница 74

Страница: 74 / 346

3. Configure the settings for the network as follows:

For control network

Setting...

Ethernet

is required

Type

Control

is required

Usage

None

is required. This is true even on a redundant K2 SAN. (Only the

iSCSI network is redundant on a redundant K2 SAN.)

Redundancy

Control

is recommended

Name

Unselected

is required

Exclude from Host
Files

Selected

is required

Managed

The first (lowest) IP address in the range of IP addresses managed by
SiteConfig. Required.

Base IP Address

The number of IP addresses in the range managed by SiteConfig.
Required.

Number of Addresses

The network's subnet mask. Required.

Subnet Mask

Additional network settings managed by SiteConfig. Allowed.

Gateway IP Address

Unselected

is required. Related settings are disabled.

Unmanaged

Servers providing DNS for name resolution. Allowed.

DNS Servers

Not allowed

Default Interface
Name Suffix

4. Click

to save settings and close.

Modifying the FTP/streaming network

1. In the

Network Configuration | Networks

tree view, select the K2 SAN's Site node.

The networks under that node are displayed in the list view.

K2 SAN Installation and Service Manual

2014 01 27

Planning and implementing a K2 SAN with SiteConfig

Содержание K2 SAN



























































































































































































































































































































































Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды

GRASS VALLEY K2 SAN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды