GRASS VALLEY K2 SAN Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 346

background image

Check the V: drive

Prerequisites:

•

The K2 Media Server is configured

•

The restart of the K2 Media Server after it is configured is complete

This task is required for NAS server functionality.

1. Verify that the K2 Media Server has restarted by opening the MS-DOS command prompt and

use the “ping” command.

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

Proceed as follows:

•

If you have NH servers, configure them next.

•

If you do not have NH servers, configure K2 clients and/or other iSCSI clients on the K2 SAN
next.

Configuring optional NH servers

If you have one or more optional NH K2 Media Servers, you next configure those servers. This
section applies to both NH1 (1 Gig FTP) servers and NH10GE (10 Gig FTP) servers.

NOTE: Multiple NH servers on a K2 SAN must be of the same type, either all NH1 or all NH10GE.

1. In the K2Config application tree view, select the K2 Media Server you are configuring.

2. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

2014 01 27

K2 SAN Installation and Service Manual

173

Configuring and licensing the K2 SAN

«
...
171
172
173
174
175
...
»

Содержание K2 SAN



























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SAN

Бренд: Seagate Страницы: 24

EonServ 5000 Series

Бренд: Surveon Страницы: 33

Barracuda 7200.7 ST3120025A

Бренд: Seagate Страницы: 58

Бренд: NEC Страницы: 254

Бренд: Glyph Страницы: 7

Бренд: Apricorn Страницы: 36

Бренд: IBM Страницы: 11

Бренд: Vivo Страницы: 3

Бренд: morse Страницы: 6

Бренд: U-Line Страницы: 6

Бренд: Sony Страницы: 8

BSV-M1 - StorStation NAS Server

Бренд: Sony Страницы: 58

Бренд: Seagate Страницы: 48

Бренд: Samsung Страницы: 17

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 1

HD080HJ - 80 GB Hard Drive

Бренд: Samsung Страницы: 1

HD080HJ - 80 GB Hard Drive

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды