GRASS VALLEY K2 SAN Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 346

background image

8. Click

OK

.

The Configuration File dialog box opens.

The configuration file for the media file system is displayed.

9. Verify media file system parameters.

Do not edit the configuration file for the media file system.

10. Click

Accept

.

A “…Please wait…” message box displays progress and a “…succeeded…” message confirms
the process is complete.

A message informs you that you must restart the server, however the restart at the end of the
Configure K2 Server wizard suffices, so you do not need to restart now.

11. Close the Storage Utility.

NOTE: Do not attempt to start SAN-attached systems or otherwise bring the SAN online until
instructed to do so by the documented procedure.

Next, continue with configuring the server using the K2Config application.

Configuring server A - Part 2

Configure File System Server Configuration page - Redundant K2 SAN server A

Prerequisites for connected K2 RAID storage:

•

Network and SNMP settings configured

•

Disks bound

2014 01 27

K2 SAN Installation and Service Manual

161

Configuring and licensing the K2 SAN

«
...
159
160
161
162
163
...
»

Содержание K2 SAN



























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SAN

Бренд: Addonics Technologies Страницы: 2

Бренд: Stratco Страницы: 2

Бренд: Seville Classics Страницы: 7

TVS- 72XU Series

Бренд: QNAP Страницы: 56

Бренд: Bosch Страницы: 20

Бренд: Atlas Страницы: 38

Бренд: VOLTGEAR Страницы: 16

Бренд: G SPEED Страницы: 2

Neutrino SK-2500

Бренд: Akitio Страницы: 8

Бренд: Clarke Страницы: 8

Бренд: Cavalry Страницы: 20

Бренд: TerraMaster Страницы: 13

caviar blue xl500s

Бренд: Western Digital Страницы: 59

Бренд: Kanguru Страницы: 38

Бренд: Sjobergs Страницы: 2

Portable Wireless iSSD

Бренд: Trek Страницы: 16

Бренд: Sonnet Страницы: 6

Бренд: Sonnet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды