GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 366

background image

For media (iSCSI) network interface

Setting...

Disabled, since names are excluded from the hosts file. Disregard.

Set to Default

Disabled, since names are excluded from the hosts file. Disregard.

...use Interface
Name/Aliases in
Host Files...

Disabled, since names are excluded from the hosts file. Disregard.

Aliases

Disabled, since names are excluded from the hosts file. Disregard.

DNS Suffix

4. Click

OK

to save settings and close.

About SiteConfig support on K2 devices

Before SiteConfig can be used to discover or manage a device, the device must meet the following
requirements:

•

The device must be a Microsoft Windows operating system device.

•

The device must have Microsoft .NET version 2.0 installed, as reported in the Windows
Add/Remove Programs control panel.

•

The SiteConfig Discovery Agent service must be running on the device, as reported in the
Windows Services control panel.

For K2 clients and K2 Media Servers shipped new from Grass Valley with K2 software version 7.0
or higher, these requirements are pre-installed. These requirements are pre-installed on recovery
images for these K2 systems as well. Therefore, if you suspect a problem with these requirements,
do not attempt to install SiteConfig support requirements. If you must restore SiteConfig support
requirements, re-image the K2 system.

Discovering devices with SiteConfig

Prerequisites for this task are as follows:

•

The Ethernet switch or switches that support the control network are configured and operational.
If multiple switches, ISLs are connected and trunks configured.

•

The PC that hosts SiteConfig is communicating on the control network.

•

There are no routers between the PC that hosts SiteConfig and the devices to be discovered.

•

Devices to be discovered are Windows operating system devices, with SiteConfig support
installed.

•

Devices are cabled for control network connections.

•

If discovering a device with Microsoft Windows Server 2008 operating system, the device must
have an IP address, either static or DHCP supplied.

1. Open SiteConfig.

96

K2 SAN Installation and Service Manual

02 February 2012

Planning and implementing a K2 SAN with SiteConfig

«
...
94
95
96
97
98
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: La Marche Страницы: 18

Бренд: Saftronics Страницы: 62

Бренд: M-system Страницы: 5

Бренд: Magtek Страницы: 54

Бренд: Most Страницы: 32

AEM-CAPXX-PF-EVK

Бренд: PowerFilm Страницы: 2

Бренд: iBasso Audio Страницы: 64

Бренд: PTN Страницы: 12

Бренд: Cobalt Digital Inc Страницы: 126

Бренд: AJA Страницы: 29

Video Sweep Generator MVG 10

Бренд: Kathrein Страницы: 28

Бренд: SolaX Power Страницы: 2

Бренд: Jarol Страницы: 174

TRANSICOLD 69UG15 Series

Бренд: Carrier Страницы: 60

MultyMedia TS 1

Бренд: TechniSat Страницы: 91

Бренд: GE Страницы: 55

040315-0 ILLUSTRATED

Бренд: GE Страницы: 20

Бренд: GE Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды