GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 343 | Manualshive

Страница: 343 / 366

background image

iSCSI extended (redundant FSMs)

RAID Storage

GigE Fabric

K2 SAN-attached client systems

FSM/Bridge

K2 Media Servers

FTP/Bridge

K2 Media Servers

Fibre Channel Fabric

Control Point PC

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

Key to illustrated cable paths:

Gigabit Ethernet carrying real-time media

Fibre Channel carrying real-time media

Gigabit Ethernet carrying traffic that is not

real-time media

A black/gray pair denotes redundant cables

This system differs from the Level 3R system as follows:

•

A Fibre Channel switch fabric, comprised of one or more Fibre Channel switches, is interposed
between K2 Media Servers and the RAID Storage devices. This allows more RAID Storage
devices to be connected, which provides higher bandwidth and more storage space.

•

Additional FTP/Bridge K2 Media Servers are added, providing additional iSCSI bridges to
support more clients and higher bandwidth clients.

Guidelines for this system are as follows:

•

The Fibre Channel switch fabric must be zoned.

Related Topics

Fibre Channel switch zoning

02 February 2012

K2 SAN Installation and Service Manual

343

Custom K2 SAN systems

«
...
341
342
343
344
345
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: Danfoss Страницы: 68

Бренд: JED Страницы: 4

Бренд: Wacker Neuson Страницы: 254

Бренд: D-Link Страницы: 6

Бренд: Yamaha Страницы: 30

Бренд: Aksa Страницы: 50

Бренд: DK-Technologies Страницы: 90

Бренд: Vacon Страницы: 44

Бренд: Pyramid Страницы: 39

VARIOMAT 2 11MM

Бренд: Calpeda Страницы: 64

Бренд: LEXIBOOK Страницы: 66

Бренд: Kramer Страницы: 17

Бренд: Samlexpower Страницы: 3

Бренд: leadsun Страницы: 8

Multi-Decoder MD-2

Бренд: tams elektronik Страницы: 40

Бренд: Sveon Страницы: 45

BLANKOM HDM-9500C

Бренд: Irenis Страницы: 41

Бренд: Westerbeke Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды