GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 366

GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 252

If the following system connection or component fails to respond to network communication:

•

The control connection between a K2 SAN-attached system and GigE switch “A”.

Then the following failover behavior occurs:

1. The control team on the K2 SAN-attached system fails over and communication begins on the

other control port.

2. The control communication finds a path through GigE “B” switch and across an ISL to GigE

switch “A” to reach the same control port on the same K2 Media Server.

3. Media (iSCSI) traffic keeps using the same path.
4. K2 Media Server “A” is still the media file system/metadata server. The media file system (SNFS)

and media database do not fail over.

5. The other K2 SAN-attached systems (not affected by the connection failure) keep using the same

paths for media and control, as in pre-failover behavior.

K2 client media (iSCSI) connection failover behavior

K2 RAID

K2 Media
Servers

K2 SAN-attached system

Ethernet
switches

A

A

B

B

Fibre Channel
connections

Control

Media

Control

Media

Control

FTP

Media

Control

FTP

Media

ISLs

X

Connection
Failure

Control traffic goes
to server A, which is
still the media file
system/database
server.

iSCSI traffic uses
the iSCSI adapter
on server B.

If the following system connection or component fails to respond to network communication:

•

Media (iSCSI) network “A” connection between a K2 SAN-attached system and the GigE switch

Then the following failover behavior occurs:

1. The K2 SAN-attached system drops communication on its “A” media port and begins using its

“B” media port and the “B” media (iSCSI) network. The iSCSI adapter (TOE) on the “B” K2
Media Server provides access to the Fibre Channel connected RAID storage.

2. Control traffic keeps using the same path to K2 Media Server “A”.
3. K2 Media Server “A” is still the media file system/metadata server. The media file system (SNFS)

and media database do not fail over.

252

K2 SAN Installation and Service Manual

02 February 2012

Operating the K2 SAN

«
...
250
251
252
253
254
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды