GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 237 | Manualshive

Страница: 237 / 366

background image

6. Verify or enter an IP address for the “B” media (iSCSI) network. Also enter the subnet mask.

7. Click

Next

.

The Database Client Configuration page opens.

Configure Database Client Configuration page - K2 client

This page connects the SAN client as a media database client to the K2 Media Server taking the
role of metadata (database) server. If there are redundant K2 Media Servers, both are listed on this
page as database servers.

1. Verify that the K2 client is connecting to the correct K2 Media Server or Servers, as follows:

•

For a basic (non-redundant) K2 SAN, the client connects to the only server.

•

For a redundant K2 SAN, the client connects to server A as database server 1 and server B
as database server 2.

If there are multiple FTP servers (such as the optional NH servers), the K2Config application
automatically assigns the SAN client to an FTP server to provide optimum FTP bandwidth across
the system. Do not attempt to change the assignment to a different FTP server while you are
doing this initial configuration.

2. Click

Check

.

3. When the wizard reports that the configuration check is successful, click

Next

.

The File System Client Configuration page opens.

02 February 2012

K2 SAN Installation and Service Manual

237

Configuring clients on the K2 SAN

«
...
235
236
237
238
239
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: VBrick Страницы: 2

Бренд: VBrick Страницы: 80

Бренд: La Marche Страницы: 21

Бренд: Rabbit Страницы: 120

Dial-to-IP 5301-DC

Бренд: Accelerated Страницы: 26

Бренд: HANYOUNG NUX Страницы: 2

Бренд: OTS Страницы: 3

Бренд: xpr Страницы: 12

Бренд: Statpower Страницы: 28

Interface Module XC Modbus

Бренд: Baer Страницы: 10

Automotive Ethernet Converter

Бренд: X2E Страницы: 22

Бренд: ImmediaTV Страницы: 93

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: StarTech.com Страницы: 24

Бренд: Patton electronics Страницы: 2

Бренд: Xantech Страницы: 2

Mega 100 Classic

Бренд: Ellumiglow Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды