GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 366

background image

Configuring NH server B

Prerequisites:

•

Server A is configured

•

The restart of server A after it is configured is complete

On nearline systems, both NH K2 Media Servers are identical, with the exception that only one
server can be the active media file system server at any time. For this reason the K2Config application
embeds the configuration and start of the media file system into the wizard when you configure the
first NH K2 Media Server, as in the previous procedure. That server is now the acting media file
system server. You can now configure the remaining server using the following procedure.

1. Verify that server A has restarted by opening the MS-DOS command prompt and use the “ping”

command.

2. In the K2 System Configuration application tree view, select the K2 Media Server you are

configuring as server B.

3. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

Configure Define Server Roles page - NH server

1. Enter the name for the K2 Media Server, as currently configured on the machine.

For Nearline server roles, selections are disabled. Leave SNFS file system server, FTP server,
and NAS server selected.

The wizard does not allow you to select Media Database Server. There is no Media Database
Server in a nearline system.

2. Click

Next

.

02 February 2012

K2 SAN Installation and Service Manual

223

Configuring and licensing the K2 SAN

«
...
221
222
223
224
225
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: UNICOM Страницы: 1

Zeverlution 3680

Бренд: Zeversolar Страницы: 2

BeoLink Converter NL/ML

Бренд: Bang & Olufsen Страницы: 45

Бренд: Sonifex Страницы: 8

Бренд: Edimax Страницы: 2

ILinx 485DRCI-PH

Бренд: B&B Страницы: 2

Бренд: Lechpol Страницы: 2

Бренд: Chord Страницы: 2

Бренд: opticis Страницы: 19

Grass Valley LUMO

Бренд: Belden Страницы: 71

Бренд: Alcad Страницы: 9

Бренд: Audiophony PA Страницы: 10

Бренд: Black Box Страницы: 20

Бренд: Extron electronics Страницы: 54

Бренд: Yangzhou Shenzhou Wind-driven Generator Страницы: 35

Бренд: NSK Страницы: 52

Бренд: V-TAC Страницы: 43

eCactus WH-SPA3.68H

Бренд: WIFO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды