GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 221 | Manualshive

Страница: 221 / 366

background image

7. Verify media file system parameters.

Do not edit the configuration file for the media file system.

8. Click

Accept

.

A “…Please wait…” message box displays progress and a “…succeeded…” message confirms
the process is complete.

A message informs you that you must restart the server, however the restart at the end of the
Configure K2 Server wizard suffices, so you do not need to restart now.

9. Close the Storage Utility.

NOTE: Do not attempt to start SAN-attached systems or otherwise bring the SAN online until
instructed to do so by the documented procedure.

Next, continue with configuring the server using the K2Config application.

Configuring NH server A - Part 2

Configure File System Server Configuration page - NH server

Prerequisites for connected K2 RAID storage:

•

Network and SNMP settings configured

•

Disks bound

•

New file system made

This page checks on the file system server role. The server also functions as a file system client,
which is also checked from this page.

1. In K2Config open the server's File System Server Configuration page, if the page is not already

open.

02 February 2012

K2 SAN Installation and Service Manual

221

Configuring and licensing the K2 SAN

«
...
219
220
221
222
223
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: Gama Sonic Страницы: 4

SOLIVIA 2.5 AP G3 TR

Бренд: Delta Страницы: 48

Бренд: OXO Страницы: 20

Бренд: Parker Страницы: 149

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: IRiver Страницы: 33

Pocketdish AV402E

Бренд: Dish Network Страницы: 2

ECO Inverter+ 25

Бренд: Oilon Страницы: 58

Бренд: Votek Страницы: 33

GX200 II Series

Бренд: Redgum Страницы: 20

SinePower MSI924

Бренд: Waeco Страницы: 436

Бренд: ViewSonic Страницы: 44

Бренд: Aegis Страницы: 20

Бренд: Parallax Страницы: 3

Бренд: Radyne ComStream Страницы: 156

Бренд: G-Power America Страницы: 55

Бренд: Grandinote Страницы: 10

Бренд: MRC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды