GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 366

background image

value. The calculator is intended for use by qualified Grass Valley personnel only. Do not attempt
to change any QOS values without guidance from Grass Valley. Doing so can result in unexpected
performance problems.

Importing a SiteConfig system description

You can import a SiteConfig system description that contains a K2 SAN into the K2Config
application. You should do this only after the K2 SAN is fully complete and implemented in
SiteConfig, as changes are not automatically synchronized between SiteConfig and K2Config after
the import.

When you import a SiteConfig system description, K2Config identifies your SAN devices, defines
the SAN, and displays the unconfigured SAN in the tree view. Therefore you do not need to define
the K2 SAN in K2Config. You can skip this task and instead begin your work in K2Config by
configuring the first K2 Media Server.

1. In the K2Config application, click

File | Import SiteConfig

.

2. Browse to and select the system configuration file.

A K2 System Information dialog box opens.

3. In the drop-down list, select the type of K2 SAN that you are importing.

4. If a redundant K2 SAN, select “…

failover capabilities

…”

5. Click

OK

.

6. The SAN appears in the K2Config application.

Configuring the basic K2 SAN - Online and Production

Work through the topics in this section sequentially to configure an Online (Tier 1) or Production
(Tier 2) basic, non-redundant K2 SAN.

Prerequisites for initial configuration - Basic K2 SAN

Before beginning your initial configuration, make sure the devices of the K2 SAN meet the following
prerequisites.

02 February 2012

K2 SAN Installation and Service Manual

127

Configuring and licensing the K2 SAN

«
...
125
126
127
128
129
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: B&B Electronics Страницы: 73

Бренд: B&B Electronics Страницы: 4

Бренд: Digitrax Страницы: 8

Бренд: Mystery Страницы: 36

Бренд: Vacon Страницы: 32

Бренд: Benchmark Страницы: 51

Бренд: EBARA Страницы: 34

Atlona OmniStream 122

Бренд: Panduit Страницы: 12

Бренд: Jaguar King Страницы: 54

Бренд: Dometic Страницы: 292

Бренд: Littfinski Daten Technik Страницы: 2

Бренд: MODIX Страницы: 26

Бренд: Actox Страницы: 36

Бренд: NANO MACHINES Страницы: 5

Бренд: Beckhoff Страницы: 40

Бренд: Samlexpower Страницы: 20

Бренд: Extron electronics Страницы: 2

1080PXX-LED Button

Бренд: EYEZONE Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды