GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 77

Страница: 77 / 338

UCP

3901

User Manual

Setting Spigot Configuration

To set a new spigot configuration, follow these steps:

1 From the

Configuration

page, select the required software from the

Software Version

pane, then select the firmware which provides the required combination of inputs,

outputs and flow standards from the list displayed on the

Card Firmware

New

pane.

Note that

Restore

and

Restart

buttons are displayed only when an item not currently

installed is selected.

2 Enable the

Reset to Defaults on Restart

checkbox. This will cause existing details

stored on the module, other than network IP settings, to be cleared down prior to

restarting the module. See

Defaults

on page 164 for more information.

3 Click

Restart

to restart the module and implement any changes made.

IMPORTANT!

Existing details must be cleared down before establishing a new

configuration

. Failure to do this may result in unexpected behavior

from the module.

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды