GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 71

Страница: 71 / 338

Essence Processing SDC

This section contains information on using an UCP

3901 / IQUCP25 / IQUCP50 card running

the Essence Processing (EP) SDC, through RollCall.
For help with the general use of the RollCall application, open the user manual by clicking

the

button on the main RollCall toolbar.

Feature Summary - UCP

3901 / IQUCP25 / IQUCP50 with Essence

Processing SDC

General Features

• Supports configuration of Ethernet links for maximum signal transport using both SFPs,

or, for dual link mode, to provide link redundancy as per SMPTE ST 2022-7. When

operating as a receiver, the UCP

3901 / IQUCP25 / IQUCP50 will dynamically adapt to

any stream presented to it.

• Supports unicast as well as IGMPv3 source-specific multicast, allowing point to point

operation or transmission in multicast groups, and forward error correction.

• Standards supported:

• 3G-SDI to SMPTE 424M/425M level A compatible
• HD-SDI to SMPTE292M/274M/296M
• SD-SDI to SMPTE259M-C
• 25GbE Ethernet to IEEE 802.3

• RollCall control and monitoring compatible with standard logging and reporting

features.

Essence Processing Features

• Handles up to 16 SDI signals over dual 25GbE IP links (dependent on SDI signal format

and compressed or uncompressed transport mode).

• Multiple transport types available for each SDI input including:

• Uncompressed video transport using either VSF TR-03 and TR-04 RTP or SMPTE-

2022-6 encapsulation.

• PCM audio using TR-03 & AES67.
• SMPTE-291M metadata support through IETF standard

RTP Payload for Ancillary

Data

• Supports frame synchronized SDI inputs with audio rate adaption, referenced to

IEEE

1588v2 (PTP) network timing (compliant with SMPTE-2059-2).

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды