GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 313

Страница: 313 / 338

313

UCP

3901

MV SDC

Chapter

User Manual

•

Cancel

- This closes the Unit Upgrade dialog. If an upgrade is in progress,

confirmation of this action is requested.

•

Upgrade

- see below.

•

Import upgrade from unit

- This creates a software release from the version

currently on the unit. Note that this option is only displayed if the unit's version is

not already in the list of software releases.

3 Select a software version from the

Software Release

dropdown.

4 Click

Upgrade

This starts the upgrade process. The Densité status LED alternates between red and

green during the upgrade process. See

Front Card-edge Interface

, on page 27.

Prior to the upgrade process beginning, a check is made to see whether the unit's

current version is available in the list of software releases. If not, a dialog displays

prompting to save the unit's current software release before upgrading.

At the end of the upgrade, if the unit does not come back online, a dialog displays.

Further attempts are made to establish contact with the unit until it either, comes back

online, or the Cancel button is pressed. Cancelling this operation has no effect on the

success or otherwise, of the upgrade operation.

To delete RollCall’s cache for the UCP

3901 / IQUCP25 / IQUCP50

If the upgrade changes any RollCall menu, then these UCP

3901 / IQUCP25 / IQUCP50

menus in RollCall may be empty or configuration information is missing or incoherent.

Always delete RollCall’s cache for the UCP

3901 / IQUCP25 / IQUCP50 after an upgrade.

1 In RollCall, right-click UCP

3901 / IQUCP25 / IQUCP50 and select Delete Cache.

Fig. 10-7: UCP

3901 Menu

2 Close and restart RollCall.

Note:

The control panel cannot be used while performing an upgrade.

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды