GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 297

Страница: 297 / 338

297

UCP

3901

Multiviewer SDC

Chapter

User Manual

RollCall Templates - Multiviewer SDC Configuration on IP port 2051

Introduction

RollCall templates for the Multiviewer SDC described here are accessed through IP port

2051 (see

Connecting to the Multiviewer SDC with RollCall for UCP

3901 Card

, on page 62).

The templates are used to configure and control the Multiviewer SDC.

Configuration/control is done using RollCall Control Panel, part of the Grass Valley RollCall

Suite. The Multiviewer SDC multiviewer configuration is typically performed once after

Multiviewer SDC installation.
RollCall Control Panel may be used to configure and control various Multiviewer SDC items,

including:

• selection of video wall layouts;
• monitoring alarm status;
• acknowledging alarms; and
• control of timer widgets on the video wall.

RollCall templates for the Multiviewer SDC

This section describes the RollCall templates for the Multiviewer SDC. See also

Navigating

Pages in the RollCall Template

•

•

•

•

•

Timer Request Protocol

, on page 307

For UCP

3901 Card templates, see

RollCall Templates - UCP

3901 Card Configuration on IP

port 2050

, on page 278.

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды