GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 243

Страница: 243 / 338

243

UCP

3901

User Manual

Main HW Build

Factory main hardware build number.

Feature PCB

(IQUCP25)

Daughter board PCB revision number.

Feature Mod Level

(IQUCP25)

Daughter board PCB modification level.

Feature HW Build

(IQUCP25)

Factory daughter board hardware build number.

Restart

Power-cycles the card. This will produce disturbances on the output

picture.
Restarting the card will affect all outputs.

Defaults

Provides options to reset the card to its defaults.

Default Settings:

All settings are reset to their default values,

except

for network configuration and IP addresses.

Factory Defaults:

All settings are reset to their default values,

including

network configuration and IP addresses.

Remove Licenses Click to remove any license currently enabled on the card. A restart is

required for this to take effect.

Parameter

Description

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды