GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 160

Страница: 160 / 338

160

Essence Processing SDC

RollTrack

RollTrack

The

RollTrack

page sets up RollTrack setting for the UCP

3901 / IQUCP Card to allow

information to be sent, through the RollCall network, to other compatible units connected

on the same network.
The

Source

window lists the RollTrack sources:

Figure 6 - 38:

Source Pane

Parameter

Description

Disable All

When checked, all RollTrack items are disabled.

Index

This slider allows up to 32 distinct RollTrack outputs to be set up.

Dragging the slider selects the RollTrack Index number, displayed

below the slider. Clicking

selects the default preset value.

Source

The source of information that triggers transmission of data is

selected with this control. Dragging the slider selects the RollTrack

source, displayed below the slider. Clicking

selects the default

preset value. When no source is selected,

Unused

is displayed.

Unused:

No RollTracks sent.

Input N OK:

Input N is good.

Input N LOST:

Input N is bad.

Where N is the input number

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды