Grandstream Networks UCM6510 Скачать руководство пользователя страница 326 | Manualshive

Страница: 326 / 483

background image

P a g e

|

325

UCM6510 IP PBX User Manual

Version 1.0.20.31

4. Go to UCM6510 Web GUI



Extension/Trunk



Inbound Routes

page. Create a new inbound route

and set the default destination to the Fax extension.

Figure 212: Inbound Route to Fax Extension

5. Once successfully configured, the incoming Fax from external Fax machine to the PSTN line number

will be converted to PDF file and sent to the Email address

[email protected]

as attachment.

Fax Sending

The UCM6510 supports sending Fax via Web GUI access. This feature can be found on Web GUI



Value-

added Features



Fax

Sending

page

.

In order to send fax, pre-setup for analog trunk and outbound route

is required.

Note:

Only A3, A4 and B4 paper sizes are supported for the Fax Sending

.

After making sure analog trunk or VoIP Trunk is setup properly and UCM6510 can reach out to PSTN

numbers via the trunk, on Fax Sending page, enter the fax number and upload the file to be faxed. Then
click on “Send” to start. The progress of sending fax will be displayed in Web GUI. Users can also view the

sending history is in the same web page.

«
...
324
325
326
327
328
...
»

Содержание UCM6510




































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UCM6510

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

Бренд: Klark Teknik Страницы: 50

Бренд: Zonet Страницы: 53

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: Advantech Страницы: 66

Бренд: Hama Страницы: 24

Бренд: SMC Networks Страницы: 56

Бренд: Handicare Страницы: 60

Бренд: Zalip Страницы: 76

Бренд: Tripp Lite Страницы: 3

Бренд: ATTO Technology Страницы: 2

Бренд: Idis Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды