Grandstream Networks UCM6510 Скачать руководство пользователя страница 201

Страница: 201 / 483

P a g e

200

UCM6510 IP PBX User Manual

Version 1.0.20.31

Name configured.

Auto Record

Enable automatic recording for the calls using this trunk (for SIP trunk only).

The default setting is disabled. The recording files are saved in external

storage device if plugged in and can be accessed under Web

GUI



CDR



Recording Files

DAHDI Out Line Selection

Select DAHDI line type. Default: Ascending

Direct Callback

Allows external numbers the option to get directed to the extension that last

called them.

Notes



Allows external numbers the option to get directed to the extension that

last called them.



Direct Callback option will be hidden if E&M Immediate or E&M Wink

is selected for the Edit T1 Port



Signaling field due to not being

applicable.

Fax Detection

Enable to detect Fax signal from the trunk during the call and send the

received Fax to the default Email address in Fax setting page under Web

GUI



Call Features



Fax/T.38

Note:

If enabled, Fax Pass-through cannot be used.

Direct Outward Dialing (DOD) via Digital Trunks

Please refer to section [Direct Outward Dialing (DOD) via VoIP Trunks].

Digital Trunk Troubleshooting

After configuring the digital trunk on the UCM6510 as described above, and it does not work as expected,

users can start and download a signaling capture from the

Maintenance



Signaling

Troubleshooting

page for analysis.

Depending on the signaling selected for the digital trunk, users can go to following pages to capture trace:

PRI Signaling Trace: Web GUI



Maintenance



Signaling

Troubleshooting



PRI Signaling Trace

SS7 Signaling Trace: Web GUI



Maintenance



Signaling

Troubleshooting



SS7 Signaling Trace

MFC/R2 Signaling Trace: Web GUI



Maintenance



Signaling

Troubleshooting



MFC/R2 Signaling

Trace

E&M Trace: Web GUI



Maintenance



Signaling

Troubleshooting



E&M Immediate Record Trace

Here is the step to capture trace:

1. Click on "Start" to start capturing trace. The output result shows "Capturing..."

2. Once the test is done, click on "Stop" to stop the trace.

3. Click on "Download" to download the trace.

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды