Grandstream Networks UCM6510 Скачать руководство пользователя страница 188

Страница: 188 / 483

P a g e

187

UCM6510 IP PBX User Manual

Version 1.0.20.31

Table 50: Analog Hardware Configuration Parameters

Tone Region

Select country to set the default tones for dial tone, busy tone, ring tone and

etc to be sent from the FXS port. The default setting is

“United States of

America (USA)

”.

Advanced Settings

FXO Opermode

Select country to set the On-Hook Speed, Ringer Impedance, Ringer

Threshold, Current Limiting, TIP/RING voltage adjustment, Minimum

Operational Loop Current, and AC Impedance as predefined for your

country

’s analog line characteristics. The default setting is “USA”.

FXS Opermode

Select country to set the On-Hook Speed, Ringer Impedance, Ringer

Threshold, Current Limiting, TIP/RING voltage adjustment, Minimum

Operational Loop Current, and AC Impedance as predefined for your

country

’s analog line characteristics. The default setting is “United States of

America (USA)

”.

FXS TISS Override

Configure to enable or disable override Two-Wire Impedance Synthesis

(TISS). The default setting is No.

If enabled, users can select the impedance value for Two-Wire Impedance

Synthesis (TISS) override. The

default setting is 600Ω.

PCMA Override

Select the codec to be used for analog lines. North American users should

choose PCMU. All other countries, unless already known, should be

assumed to be PCMA. The default setting is PCMU.

Note:

This option requires system reboot to take effect.

Boost Ringer

Configure whether normal ringing voltage (40V) or maximum ringing

voltage (89V) for analog phones attached to the FXS port is required. The

default setting is

“Normal”.

Fast Ringer

Configure to increase the ringing speed to 25HZ. This option can be used

with

“Low Power” option. The default setting is “Normal”.

Low Power

Configure the peak voltage up to 50V during

“Fast Ringer” operation. This

option is used with

“Fast Ringer”. The default setting is “Normal”.

Ring Detect

If set to

“Full Wave”, false ring detection will be prevented for lines where

Caller ID is sent before the first ring and proceeded by a polarity reversal,

as in UK. The default setting is

“Standard”.

FXS MWI Mode

Configure the type of Message Waiting Indicator on FXS lines. The default

setting is

“FSK”.



FSK:

Frequency Shift Key Indicator



NEON:

Light Neon Bulb Indicator.

FXO Frequency Tolerance

Allows users to adjust the tolerance of the FXO ringing frequency. 63Hz is

considered the standard value and is selected by default.

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Бренды по названию

Популярные бренды