Grandstream Networks UCM6510 Скачать руководство пользователя страница 142

Страница: 142 / 483

P a g e

141

UCM6510 IP PBX User Manual

Version 1.0.20.31

Click on the tab to view or edit options belonging to that category. The configuration parameters are as

follows.

Table 31: SIP Extension Configuration Parameters

– Basic Settings

General

Extension

The extension number associated with the user.

Note

: This filed supports (+) sign.

CallerID Number

Configure the CallerID Number that would be applied for outbound calls

from this user.

Note:

The ability to manipulate your outbound Caller ID may be limited by

your VoIP provider.

Permission

Assign permission level to the user. The available permissions are

“Internal”, “Local”, “National” and “International” from the lowest level to

the highest level. The default setting is

“Internal”.

Note:

Users need to have the same level as or higher level than an

outbound rule

’s privilege to make outbound calls using this rule.

SIP/IAX Password

Configure the password for the user. A random secure password will be

automatically generated. It is recommended to use this password for

security purpose.

Auth ID

Configure the authentication ID for the user. If not configured, the

extension number will be used for authentication.

Note

: This filed supports (+) sign.

Voicemail

Configure Voicemail. There are three valid options and the default option

is "Enable Local Voicemail".



Disable Voicemail

: Disable Voicemail.



Enable Local Voicemail

: Enable voicemail for the user.



Enable Remote Voicemail

: Forward the notify message from

remote voicemail system for the user, and the local voicemail will

be disabled.

Note:

Remote voicemail feature is used only for

Infomatec (Brazil).

Voicemail Password

Configure the password to access the extension's voicemail. A randomly

generated password is used by default and is highly recommended for

security. Only digits are supported.

Skip Voicemail Password

Verification

If enabled, users can skip password verification when dialing in via the My

Voicemail feature code. This option is disabled by default.

Send Voicemail to Email

If enabled, the voicemail will be attached to the email notification that is

sent when a voicemail is received. Note: When set to "Default", the global

settings in

Call Features



Voicemail



Voicemail Email Settings

will be

used.

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды