Grandstream Networks UCM6510 Скачать руководство пользователя страница 122

Страница: 122 / 483

P a g e

121

UCM6510 IP PBX User Manual

Version 1.0.20.31

Configure the location where wallpapers are stored.



File

“URL” is selected as source, specify the URL of the wallpaper file. If

“Local UCM Server” is selected as source, click to upload wallpaper

file to the UCM6510.

Screen Resolution 320 x 240

Check this option if the SIP endpoint uses a 320x240 resolution wallpaper.



Source

Configure the location where wallpapers are stored.



File

“URL” is selected as source, specify the URL of the wallpaper file. If

“Local UCM Server” is selected as source, click to upload wallpaper

file to the UCM6510.

Table 28: Global Policy Parameters

– Communication Settings

Email Settings

SMTP Settings

Check this option to configure the email settings that will be sent to the

provisioned phones:



Server

IP address of the SMTP server



Port

SMTP server port



From E-Mail address

Email address



Sender Username

Username of the sender



Password Recovery Email

Email where recovered password will be sent



Alarm receive Email 1

Email address where alarms notifications will be sent



Alarm receive Email 1

Email address where alarms notifications will be sent



Enable SSL

Enable SSL protocol for SMTP

FTP

Check this option to configure the FTP settings that will be sent to the

provisioned phones:

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды