Grady-White Boats Seafarer 228 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 66

Grady-White Boats Seafarer 228 Скачать руководство пользователя страница 31

5-1

Chapter 5: Instrumentation

ChapTer 5: INSTrUMeNTaTION aND

SWITCheS

Yamaha Instrumentation Panel

Grady-White installs full Yamaha Command Link or Command Link Plus instrumentation on all

boats. The instruments are powered by the ignition key(s) and will operate when the ignition
switch(es) is in the “on” position.

Yamaha Command Link CL7 Display (Digital Engines & Helm

Master™)

The Yamaha display provides engine and boat information listed below. The display of these

functions and other graphics may be customized. Please see the Yamaha owner’s manual for
detailed instructions on customizing.

•

Fuel Level

This feature indicates the gas tank(s)’ fuel level. Remember two things when reading this

gauge:

• The accuracy of your gauge varies with the attitude of your boat in the water (trim or list).
• The fuel pickup tube inside the gas tank is not capable of withdrawing all of the fuel from

the tank.

«
...
29
30
31
32
33
...
»

Содержание Seafarer 228



































































Отзывы:

Нет отзывов