Graco WB3000 Скачать руководство пользователя страница 50

Страница: 50 / 78

Repair

Gun Barrel Removal

1. See

Prepare the Gun for Service, page 47

2. Remove the air inlet ﬁtting (21) and take the

bracket (B) off the gun handle (16).

3. Loosen the two screws (6).

NOTICE

To avoid damaging the power supply (11),

pull the gun barrel straight away from the gun

handle. If necessary, gently move the gun

barrel from side to side to free it from the gun

handle.

4. Hold the gun handle (16) with one hand and pull

the barrel (1) straight off the handle.

Figure 27 Gun Barrel Removal

Gun Barrel Installation

1. Be sure the gasket (5*) and grounding spring

(37a) are in place. Make sure the gasket air

holes are aligned properly. Replace the gasket if

damaged.

2. Make sure the spring (11a) is in place on the

tip of the power supply (11). Liberally apply

dielectric grease (57) to the tip of the power

supply. Place the gun barrel (1) over the power

supply and onto the gun handle (16).

3. Tighten the two screws (6) oppositely and evenly

(about a half turn past snug). Do not over-tighten

the screws (6).

4. Position the bracket (B) on the gun handle (16)

and secure with the air inlet ﬁtting (21).

5. See

Test Gun Resistance, page 36

Figure 28 Gun Barrel Installation

3A2497C

Содержание WB3000















































































Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды

Graco WB3000, Инструкция - Каталог запасных частей

Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды