background image

Installation 

3A6939B

7

Installation

Grounding 

Pump: use a ground wire and clamp (not included). See 
F

IG

. 2 Loosen the locknut (W) of the grounding lug (Z). 

Insert one end of the wire (Y) in the ground lug and 
tighten the locknut securely. Connect the ground clamp 
to a true earth ground. Order Part No. 237569, Ground 
Wire and Clamp.

Fluid Hoses: use only electrically conductive hoses 
with a maximum of 500 ft. (150 m) combined hose 
length to ensure grounding continuity. Check the electri-
cal resistance of hoses. If total resistance to ground 
exceeds 25 megohms, replace hose immediately. 

Hydraulic power supply: follow manufacturer’s recom-
mendations.

Surge tank: use a ground wire and clamp.

Dispense valve: ground through a connection to a 
properly grounded fluid hose and pump.

Fluid supply container: follow local code.

Object being sprayed: follow local code.

Solvent pails used when flushing: follow local code. 
Use only conductive metal pails, placed on a grounded 
surface. Do not place the pail on a non-conductive sur-
face, such as paper or cardboard, which interrupts 
grounding continuity.

To maintain grounding continuity when flushing or 
relieving pressure: 
hold metal part of the spray gun or 
valve firmly to the side of a grounded metal pail, then 
trigger the gun or open the valve.

Mounting

The pump can be mounted using one of the following 
options:

Stand mount: Kit 253692

Wall mount: Kit 255143

Floor mount: 

Kit 19Y313—Complete kit

Kit 19Y286—Plate for mounting to an existing 
floor mount

Pump Mounting Kits manual 311619 describes the 
mount parts and how to install each.

The equipment must be grounded to reduce the risk 
of static sparking. Static sparking can cause fumes to 
ignite or explode. Grounding provides an escape wire 
for the electric current.

F

IG

. 2 Ground Wire

TI15854a

Z

Y

W

Содержание Viscount High-Flo Plus 25E932





















Отзывы: