Graco SD 10 Series Скачать руководство пользователя страница 18

Страница: 18 / 54

Installation

3A8626A

4. Connect the supply line to the hose reel inlet using

the hose inlet kit (see

Typical Installation

, F

. 1,

page 7).

NOTE: The hose reels listed in this manual do not come

with a Hose Inlet Kit.

5. Flush the hose following the instructions in

Flush

the Equipment

, page 9.

Hose Installation

Installation of Hose on a Bare Reel

1. Locate the length of the hose in the table and note

the number of revolutions the spool must be turned

to properly pre-set the spring tension.

2. Secure the reel to a solid surface with C-clamps (C)

. 9)

3. Place a piece of tape on the side of the reel flange

as a visual reference to count the number of

revolutions.

. 14

105

Hose Length

No. of Spool Turns

35 ft (10.7 m)

50 ft (15.2 m)

65 ft (19.8 m)

SPRING TENSION HAZARD

The hose reel spring is always under great tension,

which if released in an uncontrolled manner could

cause serious injury.
• Never allow the reel to spin freely. Uncontrolled

spinning could cause serious injury if hit by the

hose.

• Securely fasten the reel in place while making

adjustments.

• The hose reel spring is not a serviceable part. Do

not attempt to replace or service the hose reel

spring.

• Always wear heavy gloves while adjusting the

spring tension to protect your hands from being

cut on the hose reel.

Содержание SD 10 Series























































Результаты поиска

Содержание SD 10 Series

Отзывы:

Бренды по названию

Популярные бренды

Graco SD 10 Series, Руководство пользователя

Результаты поиска

Содержание SD 10 Series

Отзывы:

Бренды по названию

Популярные бренды