Graco Pro Xp 60 WB, Инструкция по эксплуатации

Страница: 87 / 96

Spray Tip Selection Chart (Model L60M19 MRG Gun Only)
AEF AEF AEF Fine Fine Fine Finish Finish Finish Pre Pre Pre---Orifice Orifice Orifice Spray Spray Spray Tips Tips Tips
Recommended for high finish quality applications at low and medium pressures. AEF tips have a pre-orifice
that assists in atomizing sheer thinning materials, including lacquers.
Order desired tip, Part Part Part No. No. No. AEFxxx, AEFxxx, AEFxxx, where xxx = 3–digit number from the matrix below.
Fluid Fluid Fluid Output Output Output
flfl
fl oz/min
oz/min
oz/min (l/min)
(l/min)
(l/min)
Maximum Maximum Maximum Pattern Pattern Pattern Width Width Width at at at 12 12 12 in. in. in. (305 (305 (305 mm) mm) mm)
in. in.
in. (mm)
(mm)
(mm)
6 6
6---8
8
8 (150
(150
(150---
200) 200) 200)
8 8
8---10
10
10
(200 (200 (200---250) 250) 250)
10 10
10---12
12
12
(250 (250 (250---300) 300) 300)
12 12
12---14
14
14
(300 (300 (300---350) 350) 350)
14 14
14---16
16
16
(350 (350 (350---400) 400) 400)
16 16
16---18
18
18
(400 (400 (400---450) 450) 450)
Orifice Orifice Orifice
Size Size
Size
in. in. in. (mm) (mm) (mm)
at at
at 600
600
600 psi
psi
psi
(4.1 (4.1 (4.1 MPa, MPa, MPa,
41 41 41 bar) bar) bar)
at at
at 1000
1000
1000
psi psi psi (7.0 (7.0 (7.0
MPa, MPa, MPa, 70 70 70
bar) bar)
bar)
Spray Spray
Spray Tip
Tip
Tip
0.008
(0.203)
5.6 (0.17) 7.7 (0.22)
608
0.010
(0.254) 9.5 (0.28) 12.5
(0.37) 310 410 510 610 710 810
0.012
(0.305) 12.0
(0.35) 16.0
(0.47) 312 412 512 612 712 812
0.014
(0.356) 16.0
(0.47) 21.0
(0.62) 314 414 514 614 714 814
0.016
(0.406) 20.0
(0.59) 26.5
(0.78) 416 516 616 716
* Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT) where QT = fluid
output (fl oz/min) at 600 psi from the above table for the selected orifice size.
Round Round
Round Spray
Spray
Spray Tips
Tips
Tips
To convert the gun to a round spray pattern, use
round spray conversion kit 24N391. See manual
3A2499.
Approximate Approximate
Approximate Flow
Flow
Flow Rates
Rates
Rates for
for
for Light
Light
Light to
to
to Medium
Medium
Medium Viscosity
Viscosity
Viscosity Coatings
Coatings
Coatings
(20–40 (20–40 (20–40 centipoise)* centipoise)* centipoise)*
Part Part
Part No.
No.
No.
Size Size
Size No.
No.
No.
300 300 300 psi psi psi (2.1 (2.1 (2.1 MPa, MPa, MPa, 21 21 21 bar) bar) bar) 600 600 600 psi psi psi (4.2 (4.2 (4.2 MPa, MPa, MPa, 42 42 42 bar) bar) bar) 1200 1200 1200 psi psi psi (8.4 (8.4 (8.4 MPa, MPa, MPa,
84 84 84 bar) bar) bar)
236836 4A 2.5 oz/min (73 cc/min) 4.1 oz/min (120 cc/min) 5.7 oz/min (170 cc/min)
236837 6A 2.9 oz/min (86 cc/min) 5.1 oz/min (150 cc/min) 7.4 oz/min (220 cc/min)
236838 7A
3.2 oz/min (95 cc/min) 5.4 oz/min (160 cc/min) 7.8 oz/min (230 cc/min)
236839 5B 5.4 oz/min (160 cc/min) 7.8 oz/min (230 cc/min) 11.0 oz/min (330 cc/min)
236840 7B 7.1 oz/min (210 cc/min) 9.1 oz/min (270 cc/min) 14.2 oz/min (420 cc/min)
236841 9B 8.8 oz/min (260 cc/min) 11.8 oz/min (350 cc/min) 17.9 oz/min (530 cc/min)
236842 11B 11.8 oz/min (350 cc/min) 16.2 oz/min (480 cc/min) 23.7 oz/min (700 cc/min)
* Flows are based on white acrylic, enamel paint.
3A7504A 87