background image

Installation

3A1450B

5

Installation

Grounding

Pump: use a ground wire and clamp (Y). See F

IG

. 1

Loosen the grounding lug locknut (W) and washer. 
Insert one end of the ground wire into the slot in the lug 
and tighten the locknut securely. Connect the ground 
clamp to a true earth ground. Order Part No. 237569, 
Ground Wire and Clamp.

Air and fluid hoses: use only electrically conductive 
hoses with a maximum of 500 ft. (150 m) combined 
hose length to ensure grounding continuity. Check the 
electrical resistance of hoses. If total resistance to 
ground exceeds 25 megohms, replace hose immedi-
ately.

Air compressor: follow manufacturer’s recommenda-
tions.

Surge tank: use a ground wire and clamp.

Dispense valve: ground through a connection to a 
properly grounded fluid hose and pump.

Fluid supply container: follow local code.

Object being sprayed: follow local code.

Solvent pails used when flushing: follow local code. 
Use only conductive metal pails, placed on a grounded 
surface. Do not place the pail on a nonconductive sur-
face, such as paper or cardboard, which interrupts 
grounding continuity.

To maintain grounding continuity when flushing or 
relieving pressure: 
hold metal part of the spray gun 
firmly to the side of a grounded metal pail, then trigger 
the gun.

Stand Mount

Order Part No. 253692 Pump Stand Kit (accessory). 
Mount the pump in the pump stand and secure with the 
four screws and lockwashers supplied in the kit.

See Mounting Hole Layouts on page 17. Secure the 
stand to the floor with M19 (5/8 in.) bolts which engage 
at least 152 mm (6 in.) into the concrete floor to prevent 
the pump from tipping.

Wall Mount

Order Part No. 255143 Wall Bracket Kit (accessory).

1.

Ensure the wall is strong enough to support the 
weight of the pump assembly and accessories, fluid, 
hoses, and stress caused during pump operation.

2.

Ensure that the mounting location has sufficient 
clearance for easy operator access.

3.

Position the wall bracket at a convenient height, 
ensuring that there is sufficient clearance for the 
fluid suction line and for servicing the lower.

4.

Drill four 7/16 in. (11 mm) holes using the bracket as 
a template. Use either of the two mounting hole 
groupings in the bracket. See Mounting Hole Lay-
outs
, page 17.

5.

Bolt the bracket securely to the wall using bolts and 
washers designed to hold in the wall’s construction.

6.

Attach the pump assembly to the mounting bracket. 

7.

Connect air and fluid hoses. 

The equipment must be grounded. Grounding 
reduces the risk of static and electric shock by 
providing an escape wire for the electrical current 
due to static build up or in the event of a short circuit.

F

IG

. 1. Ground Wire

TI0720a

W

Y

Содержание President 24H627





















Отзывы: