Graco PrecisionFlo 233678 Скачать руководство пользователя страница 1

Страница: 1 / 20

Instructions – Parts List

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PrecisionFlo

Metering Valve Upgrade

3500 psi (24 MPa, 240 bar) Maximum Working Fluid Pressure

For use when dispensing fluids that meet at least
one of the following conditions for non-flammability:

The fluid has a flash point above 140

F (60

and a maximum organic solvent concentration of
20%, by weight, per ASTM Standard D93.

The fluid does not sustain burning when tested per
ASTM Standard D4206 Sustained Burn Test.

Part No. 233678

PrecisionFlo Metering Valve for PVC application

Part No. 233679

PrecisionFlo Metering Valve for HemFlange application

Table of Contents

Symbols

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation and Maintenance

. . . . . . . . . . . . . . . . . . . .

Pressure Relief Procedure

. . . . . . . . . . . . . . . . . . .

Operating the Metering Valve

. . . . . . . . . . . . . . . . .

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting the Metering Valve

. . . . . . . . . . .

Fluid Needle and Seat Assembly Service

. . . . . .

Closer Service

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacing the Pressure Sensor

. . . . . . . . . . . . . .

Wiring Diagram

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Part No. 233678, Metering Valve Assembly

. . . .

Part No. 233679, Metering Valve Assembly

. . . .

Part No. 233590, Closer Assembly

. . . . . . . . . . .

Technical Data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Related Publications

. . . . . . . . . . . . . . . . . . . . . . . . .

Graco Standard Warranty

. . . . . . . . . . . . . . . . . . . . .

Graco Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

309384

rev.

TI1394A

Important Safety Instructions

Read all warnings and instructions in
this manual. Save these instructions.

Parts

Содержание PrecisionFlo 233678





















Результаты поиска

Содержание PrecisionFlo 233678

Отзывы:

Похожие инструкции для PrecisionFlo 233678

Бренды по названию

Популярные бренды

Graco PrecisionFlo 233678, Инструкция-перечень запасных частей

Результаты поиска

Содержание PrecisionFlo 233678

Отзывы:

Похожие инструкции для PrecisionFlo 233678

Бренды по названию

Популярные бренды