manualshive.com logo in svg

Graco Mini Fire-Ball 246775, Быстрый старт

Поделиться
Скачать
Graco Mini Fire-Ball 246775 Скачать руководство пользователя страница 1

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

Copyright 2004, Graco Inc. is registered to I.S. EN ISO 9001

Fire-Ball

®

 Oil Pumps

For non-corrosive and non-abrasive oils 

and lubricants only.

Mini Fire-Ball 225, 3:1 Bare Oil Pump, Part 246775

540 psi (3.7 MPa, 37 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Fire-Ball 300, 5:1, Bare Oil Pump, Part 203876

900 psi (6.2 MPa, 62 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Fire-Ball 425, 3:1, Bare Oil Pump, Part 237526

540 psi (3.7 MPa, 37 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Fire-Ball 425, 6:1, Bare Oil Pump, Part 238108

1100 psi (7.6 MPa, 76 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Fire-Ball 425, 10:1, Bare Oil Pump, Part 205626

1800 psi (12.4 MPa, 124 bar) Maximum Working Pressure
180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. 

Save these instructions.

Parts/Materials required

See 

page 5

Time required to rebuild pump

1 hour

Service, Repair, and Parts

309869C

Содержание Mini Fire-Ball 246775



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды