Graco Husky 515 D51 Series Скачать руководство пользователя | Manualshive

Страница: 12 / 38

background image

12

308981

Maintenance

Lubrication

The air valve is lubricated at the factory to operate with-

out additional lubrication. If you want to provide addi-

tional lubrication, remove the hose from the pump air

inlet and add two drops of machine oil to the air inlet

every 500 hours of operation or every month.

Flushing and Storage

Flush the pump to prevent the fluid you are pumping

from drying or freezing in the pump and damaging it.

Use a compatible solvent.
Always flush the pump and

relieve the pressure

before

you store it for any length of time.

Read

Pressure Relief Procedure

on page 11.

Tightening Threaded Connections

Before each use, check all hoses for wear or damage

and replace as necessary. Check to be sure all threaded

connections are tight and leak-free.
Check fasteners. Tighten or retorque as necessary.

Although pump use varies, a general guideline is to

retorque fasteners every two months. See

Preventive Maintenance Schedule

Establish a preventive maintenance schedule, based on

the pump’s service history. This is especially important

for prevention of spills or leakage due to diaphragm fail-

ure.

CAUTION

Do not over-lubricate the pump. Oil is exhausted
through the muffler, which could contaminate your fluid
supply or other equipment. Excessive lubrication can
also cause the pump to malfunction.

«
...
10
11
12
13
14
...
»

Содержание Husky 515 D51 Series







































Отзывы:

Нет отзывов

Похожие инструкции для Husky 515 D51 Series

Бренд: Waterstone Страницы: 6

Бренд: Makita Страницы: 24

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Larius Страницы: 56

Бренд: Danfoss Страницы: 20

Q HEAT R Series

Бренд: CANVAC Страницы: 88

Бренд: Gorenje Tiki Страницы: 48

Бренд: EBARA Страницы: 28

Бренд: GilAir Plus Страницы: 4

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

Бренд: Olimpia splendid Страницы: 72

Бренд: VARISCO Страницы: 18

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

Бренд: Lamborghini Caloreclima Страницы: 62

Бренд: FLOJET Страницы: 4

Бренд: All-Flo Страницы: 28

Бренд: Carlisle Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды