manualshive.com logo in svg

Graco E-flo iQ 26B543, Инсталляционные компоненты

Поделиться
Скачать
Graco E-flo iQ 26B543 Скачать руководство пользователя страница 61

Kits and Accessories

3A8217A

61

Kits and Accessories

Accessories are available from Graco. Make certain all 
accessories are adequately sized and pressure-rated to 
meet the system’s requirements.

System Kits and Accessories

Light Tower Kit, 255467

For D200s single supply systems.

See the E-Flo iQ Supply System Operation manual for 
more information.

Low Level Sensor Kit, 25E447

To install the Low Level Sensor:

1. Turn the Disconnect Switch (AZ) OFF.

2. Disconnect cable from the empty level sensor (ES).

3. Mount the low level sensor (LL) on the mounting 

bracket.

4. Connect the splitter cable (SP) to the previously 

disconnected cable.

5. Connect the splitter cable (SP) lead labeled EMPTY 

to the empty level sensor (ES).

6. Connect the splitter cable (SP) lead labeled LOW to 

the low level sensor (LL).

7. Raise/lower the low level sensor (LL) to the desired 

position to activate the sensor.

8. See the E-Flo iQ Supply System Operation manual 

to set up the low level sensor.

200 Liter (55 Gallon) Platen Cover Kits, 
255691

See the Platen Cover Kit manual for more information.

ADM Kit, 25R542

Enclosed Wet Cup Recirculation Kit

See the Enclosed Wetcup Recirculation Kit manual for 
more information.

Heat Control Box, 25R454

See 

Heat Control Box

 on page 58 for parts.

Part

Description

Qty.

24E451

MODULE, gca, adm

1

18A921

TOKEN, gca, upgrade, E-Flo iQ

1

LL

ES

SP

Содержание E-flo iQ 26B543

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды