Graco 24V672 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 30

Graco 24V672 Скачать руководство пользователя страница 15

Air Motor Repair

333397A

15

Replace Pilot Valves

1.

Stop the pump at the middle of its stroke. Perform
the

Pressure Relieve Procedure,

page 5.

2.

Disconnect the air line to the motor.

3.

Use a 10 mm socket wrench to remove the old pilot
valves (213) from the top and bottom covers.

4.

Lubricate and install the new pilot valves (213).
Torque to 95-105 in-lb (11-12 N•m).

Repair Air Motor

Disassemble the Air Motor

1.

For motors with DataTrak:

Remove the screw to

disconnect the reed switch from the air valve. See
F

IG

. 5, page 13.

2.

. 13, page 20. Use a 10 mm socket wrench

to remove four screws (211). Remove the air valve
(214) and gasket (209).

3.

Remove the muffler.

4.

Remove four screws (211) and remove the manifold
(220) and two gaskets (208).

5.

Use a 10 mm socket wrench to remove the pilot
valves (213) from the top and bottom cover.

6.

Remove the 13 mm tie bolts (B).

7.

Remove the top cover. Remove the o-ring (202).

8.

Remove the shield (206) from around the cylinder
(205). Remove the cylinder.

9.

Slide the piston assembly (219) straight up off the
bottom cover.

10. Remove o-ring (204) from around the piston.

11. Remove u-cup seals (207) and o-ring (217) from the

bottom cover.

WLD

213

213

ti12747a

B

«
...
13
14
15
16
17
...
»

Содержание 24V672































Отзывы:

Нет отзывов