Graco 24E512 Скачать руководство пользователя страница 29

Страница: 29 / 54

Maintenance

3A0232E

Anvil Replacement

For part references, see F

. 17 on this page and cutter

parts illustration on page 42.

Pressure Relief Procedure

, page 22.

Engage trigger lock.

Loosen knob (528) then remove cover (527). See
page 42.

Use hand to prevent anvil from spinning, then push
in and rotate anvil cap (AD) 90 degrees coun-
ter-clockwise to remove.

Disengage the anvil to blade cartridge tension lock-
down lever (AG).

Use the anvil to blade cartridge tension adjustment
knob (AF) to relieve the tension between the anvil
and blade cartridge.

Remove anvil (AC).

Install new anvil onto sleeve.

Install anvil cap.

10. Install cover and knob.

11.

Adjust Anvil to Blade Cartridge Tension

page 20.

Blade Cartridge Replacement

If glass is not getting cut properly, verify the tension is
correct before replacing the blade cartridge.

Pressure Relief Procedure

, page 22.

Engage trigger lock.

Remove knob (528) then remove cover (527). See
page 42.

Press and hold motor lock button (AK) to prevent
blade cartridge (AA) from spinning, then push in and
rotate blade cartridge cap (AB) 90 degrees coun-
ter-clockwise to remove. See F

. 17.

Remove the blade cartridge from sleeve (5). If nec-
essary, use a pick to aid in removing the blade car-
tridge.

Install new blade cartridge into sleeve.

Install blade cartridge cap.

Install cover and knob.

Adjust Anvil to Blade Cartridge Tension

page 20.

. 17

Blade cartridge is sharp. Always wear protective
gloves to prevent cuts when the cutter cover is
removed.

258900_3A0232_1j

Blade cartridge is sharp. Always wear protective
gloves to prevent cuts when the cutter cover is
removed.

Содержание 24E512























































Результаты поиска

Содержание 24E512

Отзывы:

Бренды по названию

Популярные бренды

Graco 24E512, Руководство по эксплуатации и ремонту

Результаты поиска

Содержание 24E512

Отзывы:

Бренды по названию

Популярные бренды