Graco 249512 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Graco 249512 Скачать руководство пользователя страница 7

Installation

311209W

7

Grounding

Hot melt dispense gun:

ground through connection to

a properly grounded supply system, pump and fluid

hose.

Pump:

ground as detailed in your separate pump

manual.

Supply system:

ground as detailed in your separate

supply system manual. See

Related Manuals

on page

Fluid hoses:

grounded through connection to a

properly grounded pump.

Fluid supply container:

follow local codes and

regulations.

Flammable liquids in the dispense area:

must be kept

in approved, grounded containers. Do not store more

than the quantity needed for one shift.

Solvent pails used when flushing:

follow local codes

and regulations. Use only conductive metal pails,

placed on a grounded surface. Do not place the pail on

a nonconductive surface, such as paper or cardboard,

which interrupts grounding continuity.

To maintain grounding continuity when flushing or

relieving pressure:

hold metal part of the gun firmly to

the side of a grounded metal pail, then trigger the

dispense gun.

The equipment must be grounded to reduce the risk

of static sparking and electric shock. Electric or static

sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock.

Grounding provides an escape wire for the electric

current.

«
...
5
6
7
8
9
...
»

Содержание 249512





















Отзывы:

Нет отзывов