manualshive.com logo in svg

Graco 249512, Руководство по эксплуатации и запасным частям

Поделиться
Скачать
Graco 249512 Скачать руководство пользователя страница 3

Warnings

311209W

3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The 

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. 

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. 

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this 

manual where applicable. 

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause 

electric shock.

•

Turn off and disconnect power at main switch before disconnecting any cables and before servicing 

or installing equipment.

•

Connect only to grounded power source.

•

All electrical wiring must be done by a qualified electrician and comply with all local codes and 

regulations.

BURN HAZARD

Equipment surfaces and fluid that is heated can become very hot during operation. To avoid severe 

burns:

•

Do not touch hot fluid or equipment.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including 

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not 

limited to:

•

Protective eyewear, and hearing protection. 

•

Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Содержание 249512





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды