Graco 233627 Скачать руководство пользователя страница 6

Страница: 6 / 40

Spray Tip Selection Table

309414N

Spray Tip Selection Table

LineLazer Tip Selection Guide.

Sprayer is supplied with tip LL5319. For additional applications, use the tip selec-

tion table as follows:

Note:

the last three digits (LL5319) of the tip part number identifies the line width and tip orifice (opening). For exam-

ple: the line width for tip LL5319 is 4 in. as shown in the table below. The tip orifice for tip LL5319 is .019 in.

LineLazer Tip Selection Table

* May require 100 mesh filter to minimize tip plugging.



Best for use with LineDriver.

# Best for cold weather applications.

How to Maximize Line Quality and Reduce Tip Wear.

Observe the following suggestions to increase line quality

and minimize sprayer tip wear.

1. Select a larger tip orifice and run the sprayer at a reduced operating pressure.

2. Running larger tip sizes (example: use tip LL5321 @ 2000 psi instead of LL5317 @ 3300 psi) will significantly

increase tip life and reduce tip plugging. It will also produce a more uniform film build across the line.

Tip Size

Line Width

Used For

221203*

2 inches

Sport court light film build

LL5213*

2 inches

Sport court heavy film build

LL5215*

4 inches

Alkyd paints only light film build

LL5217 4

inches

Alkyd paints only medium film build

LL5219

4 inches

Alkyd paints only heavy film build

LL5315

4 inches

Most traffic paints light film build

LL5317

4 inches

Most traffic paints medium film build

LL5319

4 inches

Most traffic paints medium film build

LL5321

4 inches

Most traffic paints heavy film build

LL5323

4 inches

Most traffic paints heavy film build

LL5327

4 inches

Most traffic paints heavy film build

LL5417#

4 - 8 inches

All paints and high solids traffic paints light film build

LL5419#

4 - 8 inches

All paints and high solids traffic paints medium film build

LL5421#

4 - 8 inches

All paints and high solids traffic paints heavy film build

LL5621

8 - 12 inches

All traffic paints light film build

LL5623

8 - 12 inches

All traffic paints medium film build

LL5625

8 - 12 inches

All traffic paints medium film build

LL5627

8 - 12 inches

All traffic paints heavy film build

Содержание 233627









































Результаты поиска

Содержание 233627

Отзывы:

Похожие инструкции для 233627

Бренды по названию

Популярные бренды

Graco 233627, Инструкция-перечень запасных частей

Результаты поиска

Содержание 233627

Отзывы:

Похожие инструкции для 233627

Бренды по названию

Популярные бренды