background image

Technical Specifications 

26

306556T

Technical Specifications

See the pump instruction manual for Technical Data including Wetted Parts, Port Sizes, and so on.

Topper Units

US

Metric

Maximum fluid working pressure

50:1 Ratio Fire-Ball Pump

5000 psi

34.5 MPa, 345 bar

50:1 Ratio President Pump

4000 psi

28 MPa, 280 bar

75:1 Ratio President Pump

4000 psi

28 MPa, 280 bar

36:1 Ratio GT 750 Pump

3600 psi

24.8 MPa, 248,2 bar

Maximum air pressure

50:1 Ratio Fire-Ball Pump

100 psi

0.7 MPa, 7bar

50:1 Ratio President Pump

80 psi

0.6 MPa, 6 bar

75:1 Ratio President Pump

80 psi

0.6 MPa, 6 bar

36:1 Ratio GT 750 Pump

100 psi

0.7 MPa, 7 bar

Weight

Model 226013 

50:1 Ratio Fire-Ball Pump 

122 lb

55 kg

Model 226018 

50:1 Ratio President Pump

136 lb 

61 kg

Model 244637 

75:1 Ratio President Pump

136 lb

61 kg

Model 204490

Elevator and Inductor

90 lb

41 kg

Model 25P544

36:1 Ratio GT 750 Pump

180 lb

82 kg

Maximum sound pressure tested at 100 psi (0.7 MPa, 7 bar) at 40 cycles per minute

Model 226013 

50:1 Ratio Fire-Ball Pump 

77.8 dB(A)

Maximum sound pressure tested at 100 psi (0.7 MPa, 7 bar) at 15 cycles per minute

Model 226018 

50:1 Ratio President Pump

80.9 dB(A)

Model 244637 

75:1 Ratio President Pump

80.9 dB(A)

Maximum sound pressure (tested at 3.28 ft. from equipment)

Model 25P544

36:1 GT 750 Pump

70.5 db(A)

Maximum sound power lever tested in accordance with ISO 9614-2

Model 226013 

50:1 Ratio Fire-Ball Pump 

85.6 dB(A)

Содержание 204490





























Отзывы: