GPX 250r TSE страница 85 Скачать руководство пользователя

Страница: 85 / 104

GPX MOTO

www.GPXMOTO.com + www.GPXMOTOUK.com

- 72 -

MAGNETO AND ELECTRIC STARTING PARTS OF ENGINE

REMOVAL OR INSTALLATION OF

STARTER MOTOR

The removal steps of the starter motor are as follows:

1. Remove the motor mounting bolt A

2. Remove the starting motor

Installation is carried out in the reverse order of

removal.

REMOVAL OR INSTALLATION OF

LEFT CRANKCASE COVER

The disassembly and assembly steps of the left front

cover are as follows:

1. Remove the mounting bolts of the left front cover.

2. Remove the left front cover.

3. Remove the sealing paper pad.

4. Remove the positioning pin of the left front cover.

NOTE

: Do not damage the joint surface of the cover

when removing the left front cover.

Installation is carried out in the reverse order of

removal.

The tightening torque of the left front cover mounting

bolt is: (10

～

15) N·m

NOTE

: When installing the sealing paper pad, you need

to use a new sealing paper pad.

Содержание 250r TSE









































































































Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды

GPX 250r TSE, Руководство по обслуживанию

Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды