GPX 250r TSE страница 74 Скачать руководство пользователя

Страница: 74 / 104

GPX MOTO

www.GPXMOTO.com + www.GPXMOTOUK.com

- 61 -

REMOVAL OF THE COOLING PUMP

The removal steps of the cooling pump are as follows:

1. Place a container under the engine, unscrew the

engine drain bolt A, and release the coolant in the

engine.

2. Unscrew the fastening bolts B, C, D of the water

pump cover.

3. Remove the cooling pump cover.

4. Remove the cooling pump impeller.

Check whether the impeller is damaged, the cooling

water seal is moving, and the static ring sealing surface

is abnormally worn or strained. If it is damaged, it needs

to be replaced.

Check whether the end face of the cooling pump cover is

damaged or not. Replace accordingly if damaged.

INSTALLATION OF COOLING PUMP

The installation steps of the cooling pump are as

follows:

1. Press the water seal static ring of the cooling pump

to the right cover.

2. Install the cooling pump impeller into the right

cover, and then install the cooling pump gear.

3. Lock the cooling pump gear.

Содержание 250r TSE









































































































Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды

GPX 250r TSE, Руководство по обслуживанию

Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды